Sisters, sisters, never knew such devoted sisters!
Apparently I was the only one that got the "model pose" memo
My favorite buy of the weekend. A fork made into an elephant necklace. Thank you Provo Freedom Festival.
Step One:
Gather all the supplies you will need. Of course I forgot something in the picture: tape. But it really doesn't require very many supplies. We ended up having everything on hand already. You can replace the hemp string to anything from leather thread, to twin, depending on the look you want. You do need something that is thin enough to tie.
Step Two:
Cut a length of hemp that is twice as long as your wrist plus some. You will need enough to make a loop at the top and tie the button on at the other end. I always give myself a lot more than I think I will need just in case. I hate it when I get to the end and don't have enough room to finish it off!
Step Three:
Fold your length of hemp in half and tie a knot at the folded end to make a loop. The loop should be large enough to fit your butt on of choice through it, but not so big the button will just fall out.
Step Four:
Tape the loop of your string down to the table and leave enough table space for the length of your bracelet to sit on the table (you will need to hold down the strings, so you can't tape it down to the end of the table like a normal friendship bracelet). For some reason I couldn't get my picture to rotate, sorry folks, but you get the idea. You will also want to tape the opposite end down so the strings are tight against the table with about a 1/4" in-between the two strings.
Step Five:
Thread your needle and tie it off at the end of the string. Make the doubled over string as long as you can without it running the risk of getting tangled as you sew the beads on. Once you have your thread ready, tie the knotted end onto the lefthand hemp string. I tied a triple or so knot just to insure it was tight up to the top of the string by the knot that makes the loop. You can leave the knotted end hanging until you are done with the bracelet or you can trim the loose end right away.
Step Six:
Okay, so I realized I skipped a couple of easy steps while i was taking pictures, so hopefully this will make sense. If not, please let me know! Next you want to string a bead onto the string you just tied to the hemp. After you have strung the bead on, using the needle, go under the second piece of hemp and pull the bead tight like in the picture below. Then go through the bead again. This is making a loop around the second hemp string and holding the bead in place from both sides.
Step Seven:
Now that you have gone through the bead again with the needle, go back under the 1st hemp string and pull the thread tight, fitting the bead snugly in-between the two hemp strings. Once the bead is secured and in the position you want it to be in, string another bead onto the thread and repeat the steps.
Step Eight:
Keep adding beads until you get to the desired length of bracelet, anklet or wrap around bracelet (just make the hemp thread lengths twice as long so you can double it over).
Step Nine:
Once you have all the desired beads on the hemp, it is time to secure the button. Take the tape off of the table, cut off the needle, and pull the three strings together at the end (the two hemp strings and the sewing string) to make a knot as close to the bottom bead as possible.
Below is what the knot should look like with all three strings included.
Step Ten:
Once the knot is in place, you can tie on your button and trim the sewing string off near the knot (I tied my sewing string a couple of times around the base of the knot just in case, but you don't have to). Put one hemp string thorough one set of holes and the other string through the other holes, pulling the button tight. If you have a two hole button, then string both of the hemp strings through both holes.
Step Eleven:
Turn the button over the tie the two hemp strings together to secure the bracelet. If you have a two hole button, tie the two hemp strings around the knot by the base of the bracelet.
Now you have a completed beaded friendship bracelet and you are ready to make ten more for yourself, family and friends! :) I got good enough at making them that my little sister who taught me how wanted me to make some for her rather than do them herself! Ha!
Here is what the double strand bracelet looks like (I think this one might be my favorite).
I hope you enjoyed this tutorial and that you have found a new favorite pass time while watching movies on lazy summer nights! Please comment if anything is unclear :) Hope everyone had a fantastic 4th of July!
xoxo
C.R.M.
